老矿渣新玩法 星际魔盒 折腾记② - 刷黑威联通教程 QNAP MCS7 固件分享

固件已打包，有需要迅雷下载地址的可以留言回复，好像都要吞链接，有什么好办法分享么？

MCS7刷机教程

mcs7刷机，很简单，把我的压缩包解压到FAT32格式的U盘，卸下硬盘，拔掉网线，插上 U 盘，按住 Reset 键不放，插电源，约 10 秒后松开 Reset，刷机时间约15分钟，期间会自动重启两次，刷机途中不要断电或强行重启，你看到路由里面设备上线自动获取IP后，直接打开IP就可以进入后台了。

QNAP刷机教程：

• 所需工具：螺丝刀、U盘、USB2TTL，硬盘

• 所需软件: Xshell 或者 PuTTY、

首先是拆机接TTL线，这个就不多说了，一代线序如下

TTL插电脑，装驱动，然后右击我的电脑-管理-设备管理器-端口，记下你的TTL所在COM端口

打开 PuTTY 新建 SERIAL 会话 ，端口填上一步的COM端口，速率 115200 ，点open打开会话

连上网线，保证电脑和盒子在一个网络环境，在 PuTTY 会话中按住 Esc键不放，盒子插电。这时PuTTY 开始输出信息，当界面显示 Realtek>时，松开Esc键。

从路由器后台确认自己电脑的IP，比如我的是 192.168.31.121，然后打开压缩包里面专用工具的 tftpd32，防火墙放行，确定IP是自己电脑的IP

putty输入命令

env set ipaddr 192.168.31.66 #设定盒子IP，从路由后台查看没有设备占用就行
env set serverip 192.168.31.121 #设定FTP服务器IP
tftp 0x03000000 emmc_kernel.bin
tftp 0x01ff2000 emmc_rescue_dt.bin
tftp 0x02200000 emmc_rescue_rootfs.bin

go all #通过tftp刷底层

注意：如果输入go all盒子重启，可以在go all命令几秒钟后拔掉电源线，按住复位键插入电源线，等待15秒后松开复位键，然后可以继续操作。

把压缩包里主文件 bbs.nas66.com.img 复制到U盘，插上盒子，putty会走代码，出现 Mount sda succeeded! 时说明U盘挂载完毕，输入 df 查看U盘挂载路径，然后 cd 到这个目录，比如我的：

/ # df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 379356 0 379356 0% /dev
/dev/sda 15828992 3817504 12011488 24% /tmp/usbmounts/sda #这里是挂载路径
/ # cd /tmp/usbmounts/sda
/tmp/usbmounts/sda # ls #确认一下文件能不能识别

System Volume Information bbs.nas66.com.img

没毛病输入命令开始刷机

cat bbs.nas66.com.img > /dev/mmcblk0

这里等待时间比较长，大概十几分钟吧，当putty出现 / # 可以输入命令时 输入 reboot 重启盒子。

重启时间也很久，当putty输出如下提示，果断打开这个IP，进入设置后台。

Welcome to TS-228(192.168.31.14), QNAP Systems, Inc.

NAS000509 login:

注意，设置向导会检测到有新固件，点跳过！点跳过！！点跳过！！！ 然后就是正常流程了，初始化需要插入硬盘。

设置完重启时间很久很久，直接看路由后台判断比较靠谱。

拔掉TTL线、装回机箱、然后就可以愉快的玩耍了

下面列上我的putty记录，可以核对一下步骤：

?
?hb

U-Boot 2012.07 (Nov 20 2018 - 11:37:19) ver_160517

CPU : Cortex-A7 dual core
MIS_GP1DATO[1801b114] default=0x00000008 [should be 0x1801b114,0x00000008]
MIS_GP1DIR[1801b104] default=0x040000a8 [should be 0x1801b104,0x04000028]
MUXPAD3[1800036c] default=0x00155049 [should be 0x1800036c,0x10025555]
CRT_MUXPAD1[18000364] default=0x00000000 [should be 0x18000364,0x00000000]
MIS_GP0DATO[1801b110] default=0x00000000 [should be 0x1801b110,0x00000000]
MIS_GP0DIR[1801b100] default=0x00000020 [should be 0x1801b100,0x00000020]
MUXPAD4[18000370] default=0x00155249 [should be 0x18000370,0x00155249]
20170626, setGPIO(45, 1)
20160715, ft5x06_ts reset set to 1(not reset for i2c will crash)
20170626, setGPIO(46, 1)
-- hwinit.c: set gpio39(beep), 41,43(i2c2), gpio40,42(fan_low/hi), gpio47(reset USB HUB) --
reg[0x18000368]=0x00000000 0
reg[0x18000368]=0x00ee0008 0-1
Board: Realtek QA Board
DRAM: 1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
[LY] cardtype=57, mmc->card_caps=0f
[LY] TBD : to support DDR50/HS200
[LY] SDR bus width=2
SDR select (sample/push) : 0x00/0x00
[LY] mmc->boot_caps = 203
[LY] sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x24, size:0x20e00
------------can't find tmp/factory/000BootParam.h
------------can't find tmp/factory/video_rpc.bin
tv_system=25 mode=1
----------VOUT_CONFIG_TV_SYSTEM----------
interfaceType =0x0
videoInfo.standard =0x19000000
videoInfo.enProg =0x1
videoInfo.enDIF =0x1
videoInfo.enCompRGB =0x0
videoInfo.pedType =0x1000000
videoInfo.dataInt0 =0x4000000
videoInfo.dataInt1 =0x0
hdmiInfo.hdmiMode =0x1000000
hdmiInfo.audioSampleFreq =0x3000000
hdmiInfo.audioChannelCount =0x1
hdmiInfo.dataByte1 =0x0
hdmiInfo.dataByte2 =0x0
hdmiInfo.dataByte3 =0x0
hdmiInfo.dataByte4 =0x0
hdmiInfo.dataByte5 =0x0
hdmiInfo.dataInt0 =0x1000000
-----------------------------------------
In: serial
Out: serial
Err: serial
LVDS: on
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux: 0 20170626: MUXPAD3[0 x1800036c]=0x00155049, MIS_GP1DIR[0x1801b104]=0x0400e5a8, MIS_GP1DATO[0x1801b114 ]=0x0000e508

------------can't find tmp/factory/recovery

Press Esc Key

Enter console mode, disable watchdog ...(boot_mode=0)

Realtek> env set ipaddr 192.168.31.66
Realtek> env set serverip 192.168.31.121
Realtek> tftp 0x03000000 emmc_kernel.bin
TFTP from server 192.168.31.121; our IP address is 192.168.31.66
Filename 'emmc_kernel.bin'.
Load address: 0x3000000
Loading: T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################################
done
Bytes transferred = 4370944 (42b200 hex)
Realtek> tftp 0x01ff2000 emmc_rescue_dt.bin
TFTP from server 192.168.31.121; our IP address is 192.168.31.66
Filename 'emmc_rescue_dt.bin'.
Load address: 0x1ff2000
Loading: #########
done
Bytes transferred = 32768 (8000 hex)
Realtek> tftp 0x02200000 emmc_rescue_rootfs.bin
TFTP from server 192.168.31.121; our IP address is 192.168.31.66
Filename 'emmc_rescue_rootfs.bin'.
Load address: 0x2200000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########
done
Bytes transferred = 4194304 (400000 hex)
Realtek> go all
Start Audio Firmware ...
== go rtk_call_bootm() ==
bootargs=console=ttyS0,115200 earlyprintk loglevel=4 panic=2
bootm_argv ={ bootm,3000000,-,1ff2000,}
## Booting kernel from Legacy Image at 03000000 ...
Image Name: Linux-3.10.24-rtk-nas
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4331928 Bytes = 4.1 MiB
Load Address: 00108000
Entry Point: 00108000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01ff2000
Booting using the fdt blob at 0x01ff2000
Loading Kernel Image ... OK
OK
== bootm.c boot_prep_linux(): commandline=bootargs=console=ttyS0,115200 earlypri ntk loglevel=4 panic=2 root=179:01 ro rootfstype=ext4 ==
Starting kernel ...
[ 0.074958] -- driver_register(): rtk119x-gpio
[ 0.080348] -- driver_register(): rtk119x-pinctrl
[ 0.086710] -- driver_register(): dummy
[ 0.135903] -- driver_register(): Generic PHY
[ 0.141133] -- driver_register(): usbfs
[ 0.145614] -- driver_register(): hub
[ 0.149957] -- driver_register(): usb
[ 0.371143] -- driver_register(): Venus_I2C
[ 0.580751] -- driver_register(): arm-pmu
[ 0.585968] -- driver_register(): ion-rtk
[ 0.692142] -- driver_register(): Venus_RPC
[ 0.698147] -- driver_register(): rtk_rtc
[ 0.703718] -- driver_register(): rtk-fb
[ 0.709474] -- driver_register(): vl53l0x-motion-sensor-low-act
[ 0.716564] -- driver_register(): rtk119x-al-lcd-key
[ 0.722543] -- driver_register(): rtk119x-al-default-key
[ 0.728826] -- driver_register(): rtk119x-ir
[ 0.733755] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2689 no pinctrl found -19
[ 0.744354] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2815 iso_sys_reg_base = fe007000
[ 0.755378] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2816 iso_irda_reg_base = fe007400
[ 0.766506] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default irrx-prot ocol = 1 .
[ 0.775354] NOTE : NEC = 1, RC5 = 2, SHARP = 3, SONY = 4, C03 = 5, RC6 = 6, R AW_NEC = 7, RCA = 8, PANASONIC = 9, KONKA=10, RAW_RC6 = 11
[ 0.788754] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default irtx-prot ocol = 1 .
[ 0.797592] NOTE : NEC_TX = 1, RC5_TX = 2, SHARP_TX = 3, SONY_TX = 4, C 03_TX = 5, RC6_TX = 6, RCA_TX = 7, PANASONIC_TX = 8, KONKA_TX=9
[ 0.810889] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default cust_code
[ 0.818767] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default scancode_ msk
[ 0.826954] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default custcode_ msk
[ 0.835141] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default keymap ta ble rtk_mk5_tv_key_table.
[ 0.845406] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default reg-ir-dp ir = 60 .
[ 0.855456] -- driver_register(): VenusIR
[ 0.861740] -- driver_register(): VenusIRTX
[ 0.867735] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2906 irq number = 197
[ 0.877820] Venus_IR_Init ---- begin ----
[ 0.882309] Venus_IR_Init for NEC mode
[ 0.886497] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] get reg-ir-dpir = 60ld us from dtb, regval=0x3000lx
[ 0.897609] Venus_IR_Init for NEC_TX mode
[ 0.902542] -- driver_register(): rtk_puwrap
[ 0.907781] -- driver_register(): rtk_vpu
[ 0.913223] -- driver_register(): rtk_jpu
[ 0.920031] -- driver_register(): alarmtimer
[ 0.933037] -- driver_register(): simple-framebuffer
[ 0.955792] -- driver_register(): serial8250
[ 0.961049] -- driver_register(): dw-apb-uart
[ 0.999009] -- driver_register(): sd
[ 1.004288] -- driver_register(): r8169
[ 1.009024] -- driver_register(): rtl8150
[ 1.013683] -- driver_register(): r8152
[ 1.018362] -- driver_register(): rtk119x-se
[ 1.024871] -- driver_register(): rtk_rbus
[ 1.030465] -- driver_register(): dwc3
[ 1.034726] -- driver_register(): rtk-dwc3
[ 1.040484] dwc3 18020000.dwc3: no usb2 phy configured
[ 1.047704] -- driver_register(): rtk-usb2phy
[ 1.052729] -- driver_register(): rtk-usb3phy
[ 1.057683] -- driver_register(): ehci-platform
[ 1.062797] -- driver_register(): rtk-ehci
[ 1.101010] -- driver_register(): rtk-ohci
[ 1.164892] -- driver_register(): xhci-hcd
[ 1.169512] -- driver_register(): usb-storage
[ 1.180711] -- driver_register(): rtk_hdmi
[ 1.189173] -- driver_register(): cec0
[ 1.193981] -- driver_register(): cec1
[ 1.199437] -- driver_register(): rtk119x-cpufreq
[ 1.310142] -- driver_register(): mmcblk
[ 1.314572] -- driver_register(): sdhci-rtk
[ 1.359298] -- driver_register(): rtkemmc
[ 1.400488] -- driver_register(): hid-generic
[ 1.405309] -- driver_register(): usbhid
[ 1.414847] -- driver_register(): timed-gpio
[ 1.421226] -- driver_register(): snd_alsa_rtk
[ 1.429462] -- driver_register(): snd-usb-audio
[ 1.435489] -- driver_register(): snd-soc-dummy
[ 1.440643] -- driver_register(): soc-audio
[ 1.445307] -- driver_register(): oprofile-perf
[ 1.457250] -- driver_register(): rfkill
[ 1.467329] -- driver_register(): avcpu
[ 1.953385] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Sun Dec 1 00:00:00 UTC 2013
/ # [ 2.128026] hub 3-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 2.247872] usb 3-1: == new high-speed USB device number 2 using xhci-hcd BEG [udev.idVendor=0x0000, idProduct=0x0000]
[ 2.302519] usb 3-1: == new high-speed USB device number 2 using xhci-hcd END [udev.idVendor=0x174c, idProduct=0x2074, hdev.idVendor=0x1d6b, idProduct=0x0002 , product=xHCI Host Controller, manufacturer=Linux 3.10.24-rtk-nas xhci-hcd, ser ial=xhci-hcd.2.auto]
[ 2.390557] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 2.507769] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.528614] usb 4-1: == new super-speed USB device number 2 using xhci-hcd EN D [udev.idVendor=0x174c, idProduct=0x3074, hdev.idVendor=0x1d6b, idProduct=0x000 3, product=xHCI Host Controller, manufacturer=Linux 3.10.24-rtk-nas xhci-hcd, se rial=xhci-hcd.2.auto]
[ 6.853275] prepare to U0
[ 6.873224] U0
[ 6.875015] usb 3-1: retry with reset-resume
[ 7.023871] usb 3-1: == reset high-speed USB device number 2 using xhci-hcd B EG [udev.idVendor=0x174c, idProduct=0x2074]
[ 7.077772] usb 3-1: == reset high-speed USB device number 2 using xhci-hcd E ND [udev.idVendor=0x174c, idProduct=0x2074, hdev.idVendor=0x1d6b, idProduct=0x00 02, product=xHCI Host Controller, manufacturer=Linux 3.10.24-rtk-nas xhci-hcd, s erial=xhci-hcd.2.auto]
[ 7.362755] hub 3-0:1.0: port 1, status 0503, change 0004, 480 Mb/s
[ 7.383940] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 7.390542] hub 3-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 7.492745] usb 3-1.4: == new high-speed USB device number 3 using xhci-hcd B EG [udev.idVendor=0x0000, idProduct=0x0000]
[ 7.522968] usb 3-1.4: == new high-speed USB device number 3 using xhci-hcd E ND [udev.idVendor=0x03f0, idProduct=0xe607, hdev.idVendor=0x174c, idProduct=0x20 74, product=AS2107, manufacturer=ASMedia, serial=USB2.0 Hub]
[ 7.682422] usb 3-1.4: hub_port_connect_change unbind-probe dev_name = 3-1.4 jiffies= 0x301
[ 12.719074] hub 4-1:1.0: warm reset port 1
[ 12.838933] hub 4-1:1.0: warm reset port 2
[ 14.122304] sd 1:0:0:0: [sda] No Caching mode page found
[ 14.127849] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 14.146746] sd 1:0:0:0: [sda] No Caching mode page found
[ 14.152208] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 14.176243] sd 1:0:0:0: [sda] No Caching mode page found
[ 14.181702] sd 1:0:0:0: [sda] Assuming drive cache: write through
[nas-hotplug] Mount sda succeeded!

/ # df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 379356 0 379356 0% /dev
/dev/sda 15828992 3817504 12011488 24% /tmp/usbmounts/sda
/ # cd /tmp/usbmounts/sda
/tmp/usbmounts/sda # ls
System Volume Information bbs.nas66.com.img
/tmp/usbmounts/sda # cat bbs.nas66.com.img > /dev/mmcblk0
/tmp/usbmounts/sda # reboot
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes[ 1153.531773] sdio_reset_fun...
[ 1153.534819] Stop emmc...
[ 1153.537945] Do watchdog reset directly...

?hb

U-Boot 2012.07 (Jan 27 2016 - 17:16:49)

CPU : Cortex-A7 dual core
Board: Realtek Demo Board
DRAM: 1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
[LY] cardtype=57, mmc->card_caps=0f
[LY] TBD : to support DDR50/HS200
[LY] SDR bus width=2
SDR select (sample/push) : 0x00/0x00
[LY] mmc->boot_caps = 203
[LY] sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x130, size:0x21600
get_bootparam:
------------can't find tmp/factory/000BootParam.h
Factory RO: MMC
[FAC_RO] No factory_ro data in eMMC
In: serial
Out: serial
Err: serial
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux: 0
------------can't find tmp/factory/recovery
======== Checking into android recovery ====

Start Boot Setup ...
[INFO] fw desc table base: 0x00620000, count: 6
Normal boot fw follow...
Kernel:
FW Image to 0x03000000, size=0x0058bbd0, 0x2c5e blocks (0x0358bbd0)
FW Image fr 0x008b7600, fr block 0x45bb (non-lzma)
DT:
FW Image to 0x01ff2000, size=0x000064fa, 0x33 blocks (0x01ff84fa)
FW Image fr 0x00630000, fr block 0x3180 (non-lzma)
resolution = <0x500 0x2d0>
ROOTFS:
FW Image to 0x02200000, size=0x00400000, 0x2000 blocks (0x02600000)
FW Image fr 0x01a43200, fr block 0xd219 (non-lzma)
Audio FW:
FW Image to 0x01b00000, size=0x0027f528, 0x13fb blocks (0x01d7f528)
FW Image fr 0x00638000, fr block 0x31c0 (non-lzma)
Start A/V Firmware ...
L# Booting kernel from
: gHacDy MIIma geR aatw 0 3E00n00a0b0 l..e.
MP GI mACag3e D TNaSme M:P E GLi2nu xA-3A.1C0. 20D-aDlP-2 .5W.3M
peP RImOa MgeL PTy
:
C SARPM DLiInFux KReranwel IEmnagae b(luneco:m pMPreGss edA)
B3 DDTaSta M SPiEzeG:2 AA58C1 51D84D BPy WteMsA =P R5O. M5L MP i


LFoaodr Acdder es2s:c h00 10F8o00r0m
a t: EnDTtrSy PoDinTt:S H 0D0 10A80C003
. DD PV eMLriPf yAAinCg WMChAecPkRsuOm ..



[AO][InitHDMIVideoType]HDMI Frequecny 148, resolution 25


@@@@@@@One Step TV System magic number = 0xc0de0bee, addr = 0xb8071100@@@@@@@

@@@@@@No hdmi mode
HDMIOff = 1
[VO_SetVideoStandard]st 25 p 1 1 0
[VO_SetVideoStandard]ped 1 data0 0x00000004 data1 0x00000000
[VO_SetVideoStandard]st 25 p 1 1 0
[VO_SetVideoStandard]ped 1 data0 0x00000004 data1 0x00000000
inten.i 0 hdmi 0
[VO setTVStandard 25 3D 0 0]

(TVE) TVE_DAC_mode 0,,cmd->enProg 1!! ~~comp 1, ch2 0, mode_3D 0!!
~~TVE standard#
OK
## Flattened Device Tree blob at 01ff2000
Booting using the fdt blob at 0x01ff2000
Loading Kernel Image ... OK
OK
Starting kernel ...
SetVideoStandard return!

(VO_ConfigHDMI_InfoFrame) L:232, is_hdmi_plugin 0, hdmiMode 2!!Mode 2 dataByte1 0x000000d8 0x000000dd 0x00000028
dataByte4 0x00000081 0x000000b5 int0 0x81d853c4
Mode 2 dataByte1 0x000000d8 0x000000dd 0x00000028
dataByte4 0x00000081 0x000000b5 int0 0x81d853c4
fw turn off 0xb800d044 = 0x00000000!
boot_info 0xa0000000 magic 0xffffffff en 255
[AO]check 0x 0x180056e4, HDMI Mode?(0)
[ 1.100919] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.110598] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.120594] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.160883] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.170584] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.180581] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.717952] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] get reg-ir-dpir = 50ld us from dtb, regval=0x2500lx
[ROS: openRPC() intr_scpu_dev_r buf 0x00e2ffa1 s 0x00e2ffa1 e 0x00e4ffa1 i 0 x00e2ffa1[ROS: openStubRPC() intr_scpu_dev_w buf 0x00e6ffa1 s 0x00e6ffa1 e 0x 00e8ffa1 i[AVCPU] Set Debug level 0x00000001
-------------------
Audio Version = 890778 (phoenix)
Common Version = 0
Binary src compiled at Dec 14 2015 10:26:11
Note =
-------------------




[A] gloabl malloc size 0x003ffeb8
[ 1.792546] AudioIntrRead:141 can't find process for handling AudioIntrRead p rogramID:98
[ 1.801612] AudioIntrRead: program:98 version:0 procedure:1 taskID:0 sysTID:4 294967295 sysPID:4294967295 size:4 context:81d8d5d5 atomic
[ 2.026510] dwc3 18020000.dwc3: no usb2 phy configured
[ 3.421252] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 3.920731] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 4.420232] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 4.919731] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 6.777888] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 7.277372] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 7.776871] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 8.276371] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 8.835728] rtc-rx8010 3-0032: Unable to write register #23
[ 8.841436] i2c i2c-3: probing for rx8010 failed
[ 8.852036] cpufreq: Failed to obtain VDDARM: -517
[ 8.856960] cpufreq: Only frequency scaling available
[ 8.994790] cpufreq: Failed to obtain VDDARM: -517
[ 8.999711] cpufreq: Only frequency scaling available
[ 9.065550] ilitek_init,996,ilitek.dev.remove_flag =0
[ 9.415103] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
resize2fs 1.42.9 (28-Dec-2013)
The filesystem is already 89598 blocks long. Nothing to do!

resize2fs 1.42.9 (28-Dec-2013)
The filesystem is already 20472 blocks long. Nothing to do!

[ 9.584954] hub 3-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 9.704795] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 9.812318] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 9.934710] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 10.004709] hub 3-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 10.104514] usb 3-1.4: new high-speed USB device number 3 using xhci-hcd
[ 10.274206] usb 3-1.4: hub_port_connect_change unbind-probe dev_name = 3-1.4 jiffies= 0x404
initramfs_qnap.cpio.gz: OK
md5sum check OK!
[ 11.326007] sd 1:0:0:0: [sda] No Caching mode page found
[ 11.331451] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 11.339551] sd 1:0:0:0: [sda] No Caching mode page found
[ 11.345072] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 11.353795] sd 1:0:0:0: [sda] No Caching mode page found
[ 11.359238] sd 1:0:0:0: [sda] Assuming drive cache: write through
unzip initramfs_qnap.cpio.gz Success!
49442 blocks
extract initramfs_qnap.cpio Success!
Untar /mnt/emmcp5/mnt/boot_disk/boot/rootfs2.tgz success
rootfs_tas.tgz: OK
rootfs_tas.tgz - md5sum check OK!
Untar rootfs_tas.tgz success
resize2fs 1.42.13 (17-May-2015)
The filesystem is already 15352 (1k) blocks long. Nothing to do!

[ 35.916985] fnotify: Launch the fnotify thread: 4006111424
[ 43.612972] r8169 18016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 43.621887] r8169 18016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
^A[ 47.299090] r8169 18016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay : 10).
[ 47.308027] r8169 18016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[ 70.855536] r8169 18016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 70.864480] r8169 18016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
upnpd[3763]: UPnP SDK Successfully Initialized.
upnpd[3763]: Succesfully set the Web Server Root Directory.
upnpd[3763]: IGD root device successfully registered.
upnpd[3763]: Advertisements Sent. Listening for requests ...
upnpd[3959]: UPnP SDK Successfully Initialized.
upnpd[3959]: Succesfully set the Web Server Root Directory.
upnpd[3959]: IGD root device successfully registered.
upnpd[3959]: Advertisements Sent. Listening for requests ...
[ 107.997407] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 108.004199] hub 4-1:1.0: warm reset port 1
[ 108.127959] hub 4-1:1.0: warm reset port 2
daemon_mgr PID 4491/4490
[ 112.428581] hub 4-1:1.0: warm reset port 1
[ 112.553409] hub 4-1:1.0: warm reset port 2


Welcome to TS-228(192.168.31.14), QNAP Systems, Inc.

NAS000509 login: